Visualizer

Internal operation status. Not returned by any method.

Unspecified error.

Operation failed due to bad parameter value.

Operation failed due to dead remote object.

Operation failed because it was requested in wrong state.

Operation failed due to bad object initialization.

Operation failed due to lack of memory.

Defines a measurement mode in which no measurements are performed.

Defines a measurement mode which computes the peak and RMS value in mB, where 0mB is the maximum sample value, and -9600mB is the minimum value. Values for peak and RMS can be retrieved with getMeasurementPeakRms(MeasurementPeakRms).

Defines a capture mode where the playback volume will affect (scale) the range of the captured data. A low playback volume will lead to low sample and fft values, and vice-versa.

Defines a capture mode where amplification is applied based on the content of the captured data. This is the default Visualizer mode, and is suitable for music visualization.

State of a Visualizer object that is active.

State of a Visualizer object that is ready to be used.

State of a Visualizer object that was not successfully initialized upon creation

Successful operation.

Class constructor.

Returns current capture size.

Returns the capture size range.

Get current activation state of the visualizer.

Returns a frequency capture of currently playing audio content.

This method must be called when the Visualizer is enabled.

The capture is an 8-bit magnitude FFT, the frequency range covered being 0 (DC) to half of the sampling rate returned by getSamplingRate(). The capture returns the real and imaginary parts of a number of frequency points equal to half of the capture size plus one.

Note: only the real part is returned for the first point (DC) and the last point (sampling frequency / 2).

The layout in the returned byte array is as follows:

• n is the capture size returned by getCaptureSize()
• Rfk, Ifk are respectively the real and imaginary parts of the kth frequency component
• If Fs is the sampling frequency retuned by getSamplingRate() the kth frequency is: (k*Fs)/(n/2)

Returns the maximum capture rate for the callback capture method. This is the maximum value for the rate parameter of the setDataCaptureListener(OnDataCaptureListener, int, boolean, boolean) method.

Returns the current measurement modes performed by this audio effect

Retrieves the latest peak and RMS measurement. Sets the peak and RMS fields of the supplied Visualizer.MeasurementPeakRms to the latest measured values.

Returns the sampling rate of the captured audio.

Returns the current scaling mode on the captured visualization data.

Returns a waveform capture of currently playing audio content. The capture consists in a number of consecutive 8-bit (unsigned) mono PCM samples equal to the capture size returned by getCaptureSize().

This method must be called when the Visualizer is enabled.

Releases the native Visualizer resources. It is a good practice to release the visualization engine when not in use.

Sets the capture size, i.e. the number of bytes returned by getWaveForm(byte[]) and getFft(byte[]) methods. The capture size must be a power of 2 in the range returned by getCaptureSizeRange(). This method must not be called when the Visualizer is enabled.

Registers an OnDataCaptureListener interface and specifies the rate at which the capture should be updated as well as the type of capture requested.

Call this method with a null listener to stop receiving the capture updates.

Enable or disable the visualization engine.

Sets the combination of measurement modes to be performed by this audio effect.

Set the type of scaling applied on the captured visualization data.

Invoked when the garbage collector has detected that this instance is no longer reachable. The default implementation does nothing, but this method can be overridden to free resources.

Note that objects that override finalize are significantly more expensive than objects that don't. Finalizers may be run a long time after the object is no longer reachable, depending on memory pressure, so it's a bad idea to rely on them for cleanup. Note also that finalizers are run on a single VM-wide finalizer thread, so doing blocking work in a finalizer is a bad idea. A finalizer is usually only necessary for a class that has a native peer and needs to call a native method to destroy that peer. Even then, it's better to provide an explicit close method (and implement Closeable), and insist that callers manually dispose of instances. This works well for something like files, but less well for something like a BigInteger where typical calling code would have to deal with lots of temporaries. Unfortunately, code that creates lots of temporaries is the worst kind of code from the point of view of the single finalizer thread.

If you must use finalizers, consider at least providing your own ReferenceQueue and having your own thread process that queue.

Unlike constructors, finalizers are not automatically chained. You are responsible for calling super.finalize() yourself.

Uncaught exceptions thrown by finalizers are ignored and do not terminate the finalizer thread. See Effective Java Item 7, "Avoid finalizers" for more.